Tag Archives: Navigation

Bushwalking, equipment, technology, Uncategorized

Bushwalking Equipment | Can I Really Do Without a Smartphone?

Leave a comment

As a bushwalker, can you afford not to own a smartphone? Which smartphone apps can replace dedicated equipment? What are the limitations?

Over the last few years technology has made smartphones invaluable to bushwalkers, replacing many of the devices, which previously had to be bought and carried individually.

Probably the first device carried by bushwalkers to be incorporated into the iPhone was the still and movie camera. Today’s smartphone has a high quality camera which can take video and stills, including panoramas, mark each with the location at which the photo was taken, and then upload it to the web using wifi or mobile (cellular) data.

Next, the GPS became available, allowing routes to be mapped live, waypoints determined and marked, and distances accurately determined. Recently, apps which allow the viewing of calibrated digital maps have become commonly available, and some apps now incorporate the navigation features found in a dedicated GPS. High resolution colour screens make viewing these maps and navigational features easy. Modern smartphones have built-in compasses which can be calibrated and are accurate enough for the day walker, but not accurate enough for bearings over long distances.

Then high quality heart rate sensors came on the market which could pair with a smartphone, initially using a “dongle” plugged into the earphone socket but more recently using low energy interference-free Bluetooth.

Some apps even use the smartphone camera and built-in light to measure blood flow pulses in a finger, without the need for an independent sensor. Fitness training had become more scientific!

The next advance was the ability to measure heart rate variability (HRV) (see previous post), using the powerful analysis capabilities of modern smartphones. Initially measuring HRV was only possible with expensive laboratory based equipment, but soon Polar had incorporated this ability into some of their top-of-the-line wrist computers. In the last few years, this technology has migrated to the smart phone, allowing bushwalk training to be fine tuned.

Bush walkers visiting remote areas often feel the need to take emergency devices with them to obtain help if an emergency occurs. We are all familiar with personal location beacons (PLBs) which can transmit a message, including location, to an overhead satellite, and from there to emergency rescue services.

SPOT gen3 s can send a message via satellite to your emergency contacts or to the same rescue service. Version three is much better functionally according to the reviews, but has a more expensive subscription.

Recently smartphone apps (GetHomeSafe) have become available which can send an SMS or email, if a bushwalker fails to return on time, without the need for any action by the “injured” or “lost” person or instantly in a critical emergency to a contact list or even rescue services directly, including the current location, participant details and a route plan. “You don’t need a working phone (be within range) or even to be be conscious for an alert to be sent.”

Bush walkers on day walks and within range of a mobile tower, up to 70 km from a high enough vantage point, can add weather and tide apps  and the ability to visualise routes or places in 3D using Google Earth.

We now have GPS, fitness, navigation, mapping, emergency notification and weather services available at low cost in the one device! The only problem is a lack of battery capacity, but even this can be overcome to some extent with a solar charger.

What is next?
How do you overcome these limitations?
Where will the future take us?

Creative Commons LicenseThis article by Bush Walker is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

Advertisement
Uncategorized

Bushwalking Skills | Making a Bushwalking Aide-memoire

Leave a comment

Do you lead bushwalks? Thought about carrying an aide-memoire  for emergencies? What resources will you need?

In the nineties, when I was actively upgrading my bushwalk leadership qualifications, I kept an aide-memoire to help me remember the key points of bushwalking for in-the-field examinations. This was initially kept in several “Granny’s brag books”,  4″ x 6″ photo albums with the cardboard stiffeners removed and with the individual plastic pockets sealed, then progressed to a Sharp Organiser, then to a Palm PDA and finally to my Nokia Smartphone, before being archived to a wiki (see link above). To keep the number of “album” pages to a minimum, the text was reduced to 7 pt.

The first aid was collated from Senior First Aid courses which I did with St John’s and the Red Cross, with additional information added from wilderness first aid courses and books I had read.

 Disclaimer: Although I culled information, which I knew was out-of-date, when I first set up this wiki, I have not updated the first aid information for the last few years, and as some things change every few years eg snake bite and EAR, the aide-memoire needs to be checked with an up-to-date first aid manual.

For many years, I carried this information, in note form, as a resource for emergencies, especially when leading bushwalks to remote areas of Australia. You might find such a concept useful, and perhaps be able to use the topic outline as  a worthwhile starting point.

If I was making one today, I would add it as a pdf to my Smartphone, which I usually carry with me. You could of course use your camera-equipped smartphone to copy relevant pages from books and save as a photo album. If you carry a Kindle with you, for your light reading, you have another alternative. However, in a pinch, I think “Granny’s brag book” would prove to be the most reliable of them all!

Recently I have added some excellent  leadership articles by Rick Curtis (Director, Outdoor Action Program), which no longer seem to be online at his website. This material is the Group Development and Leadership Chapter from his Outdoor Action Program Leader’s Manual. You can find some of the more useful articles in the sidebar to the right, under Bushwalking Resources, and the rest in my wiki. The text may be freely distributed for nonprofit educational use. However, if included in publications, written or electronic, attributions must be made to the author. Commercial use of this material is prohibited without express written permission from the author. Copyright © 1995 Rick Curtis, Outdoor Action Program, Princeton University.

Discussion: 
I’d love to know if you carry an “aide-memoire”, what type and what it contains.

Other related leadership articles
See Categories or Labels in the sidebar on the right.
 
  Creative Commons LicenseThis article by Bush Walker is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

Uncategorized

Bushwalking Navigation | How to make a customised, calibrated map from an .ecw map file.

1 Comment

Do you have a Mac computer? Want to know how to use a ecw map file to produce a customised, calibrated, topographic map? Don’t know which software to use? Don’t want to use a Windows emulator? Not sure which map datum to use?

UPDATE (Tuesday 3 July): advice on calibrating TOPOMaps version 2 ecw files  modified

The following discussion relates exclusively to two highly regarded Mac applications that I, and millions of other Mac users, have been using for what seems like a lifetime. Both are fully supported with user forums, have a prompt response to enquiries, are low cost for what you are getting, and are actively being updated by developers who have a love for Macs. These applications are

It is of course possible to use OziExplorer on a Windows computer or emulate a Windows machine on your Mac, but these are a poor substitute for powerful, user friendly software, running natively on a Mac.

I assume that you are using the latest version of Graphic Converter (GC) (there is a trial period so you can fully test it before purchasing) and have it running in 32 bit mode. You can do this by control clicking on the GC file icon, selecting the Get Info box and then checking the  “Open in 32 bit mode” check box if this choice is available [ see diagram] NB  ecw files won’t open in 64 bit mode and you will get an error message if you try to do so.

MacGPS Pro doesn’t have a demo version, but it does have a 30 day money-back guarantee.

iOS Applications

MacGPS Pro also has an iPhone/iPad/iTouch version iHikeGPS which is  suitable for New Zealanders and North Americans, due to the availability of free maps. Australians miss out as our maps have to be purchased.

Bit Map (Australian design) allows uploading and viewing of custom maps made using the technique outlined below, using an iPad or iPhone, which is something that few other apps can do. While its plotting features are not as complete as MacGPS Pro, it does allow the plotting of waypoints and routes,  or uploading from an OS X mapping application such as MacGPS Pro via iTunes. Like MacGPS Pro it allows live viewing of your current position using the built in GPS.

Disclaimer: I have no relationship with the  developers of the software discussed above.

For my review of Bit Map click this link.

Steps

IMPORTANT: If you have a small (a few map tiles only) .ecw file and the accompanying .map geo-referencing file is in the same  folder, then MacGPS Pro will open and calibrate the ecw file, as soon as your drop it on the MacGPS icon, without any further action on your part. If you don’t have the corresponding .map file then you will need to calibrate the newly imported ecw file as in Step 7.

    1.    Drag  the  ecw file from your CD to the GC icon, and dialogue box below will pop up. Select a slightly bigger area than you want by dragging the square corners of the large box [see diagram below] and then position the box by dragging from the middle of the box. Select Downsample.”None”, then click OK. HINT: It doesn’t need to be accurate at this stage. Just make sure the area of interest is inside the selected area.

  2.    Select the part of the image you want by using the selection tool (the dashed square, second line on the right) [see diagram] from the toolbox (bring to forefront by clicking command-K)  and save as (file/save as) a pict file, which is the native MacGPS Pro format. Make sure you have checked the radio button Save Selection Only.[see diagram below]  [Steps: name file, select file format ie PICT, check save selection only]

 3.    Open Mac GPS Pro, set the units (file/unit choices) to the appropriate datum,
which should correspond to the map datum of the paper maps you have or will be purchasing.

If you intend printing labelled maps directly from MacGPSPro as pdfs, then I would suggest you set to GDA94, as this is most likely to be compatible with the maps of others in your group.

 eg GDA94, UTM, kilometres, metres magnetic, click OK. [see diagram below]

    4.    Drag the cropped pict  file from your Finder onto the MacGPS Pro icon.
    5.    A dialogue box will open and ask you to “Set the map’s Datum  and Projection type”  [see diagram below] Select GDA94 for most discs recent mapping discs and Transverse Mercator. Click OK

    6.    It will then pop up a “Standard Coordinates for the Map” dialogue box. Enter the grid zone (see image)

and check the ‘Store calibration in PICT file” box, then OK [see diagram below]

    7.    You will then have a “Click known Points to Calibrate Map ” dialogue box pop up. Check the map datum is set to the same as your hard copy maps before proceeding. [see diagram below]

Complete this for any four easily recognized features (eg trig point, windmill)  located near the four corners of the map, using a hard copy of the map to provide the 7 digit eastings [eg 0262600] and northings [eg 6553800]. Click DONE.

HINT: Make sure you have zoomed in as far as you can, without the map becoming too pixelated, using the zoom icon top right, to increase your accuracy.
 
VERY IMPORTANT: If you are using an ecw file from a TOPOMaps version 2 disc (South Australian), then be aware that the grid lines on the ecw file are those of the AGD84 datum, as the file has been scanned from pre-94 maps. If however, you open these maps in OziExplorer you will find that the associated .map file (found on the disc) has calibrated the maps as GDA94 hence the disc markings.

The Instructions file on the disc ( who reads the instructions?!) say

The map image displayed (in OziExplorer) has been recalibrated to the Geocentric Datum of Australia 1994 (GDA94). The Easting and Northing readouts for any point at the cursor position will in GDA (94) coordinates.

Please Note:
The map images were scanned from AMG 84 based maps. Therefore, if the cursor is placed at the intersection of two grid lines, the coordinate readout will not correspond to the values of those grid lines. Future map editions will display a grid pattern based on the GDA94 datum and therefore the readout will then correspond to the grid values. See also p25

The warning above is very important, if you normally use grid line intersections as your calibration points, as this will result in inaccurate calibration, with the whole map displaced 100-200m. If you use recognized topographic features this problem doesn’t exist.

HINT: To speed up the process in case you need to start over again, keep a record by printing a copy of the map and annotating it with the four corner grid references which you previously entered. If MacGPS Pro won’t let you click the DONE button it is probably because you made a mistake entering the GR and will need to start again, or perhaps you have failed to select a point on the map, to register the grid reference.

The Ultimate Goal

Remember that the goal of calibrating a map, plotting waypoints and joining them to form a route using MacGPS Pro is so that you can transfer them to your GPS and use your GPS to find your location relative to these waypoints, on either a purchased map or one printed using the software. For this reason, the map datum set in your GPS MUST match the paper map you are carrying.

My next few posts will explain how to export your data from MacGPS Pro to your GPS, overlay the calibrated map you have produced on Google Earth to help you visualize the terrain and get the UTM coordinates from Google Earth by overlaying with UTM grid.

Visit some of my other related navigation posts

  Creative Commons LicenseThis article by Bush Walker is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

Uncategorized

Bushwalking Navigation | Documenting Your Route Plan

3 Comments

How do you document a route plan? How can you use Google Earth to check the route and save pics of critical navigational decision points? How do you use mapping software to plot and export the waypoints to your GPS, print the route and elevation graph? How can you annotate your map pdfs? How do you protect your maps from the weather?

This post is part 2 of  Bushwalking Navigation | A Route Plan Workflow

Getting the “big picture”

The first step in planning any trip is to read guide books, talk to other bushwalkers and search  bushwalking forums, websites and blogs to discover which routes are popular. 

Once you have decided on your intended route you will need to check water availability, weather conditions, locate existing tracks, property boundaries and permitted camping spots.  Don’t forget to check photographic websites such as Flickr, which give a good idea of popular sites and the scenery to be expected.

Next study the terrain to work out your likely speed, keeping in mind height gains and losses, the density of vegetation, the amount and difficulty of any off-track walking, and the presence of waterfalls in creek lines, which may need to be bypassed.  Once you know these you will be able decide how far apart your camping spots can be and determine each day’s starting and finishing times.

I have discussed many of these navigation techniques and route plan design in previous posts (21) and won’t go further into detail now.

Finding a Map

You should never rely solely upon a GPS for critical navigational decisions and for this reason bushwalkers should always carry topographic maps covering the route, and the surrounding countryside just in case you get off track. These can be purchased from a local map or outdoors shop, and are usually available at 1:50,000 scale but sometimes at 1:25,000, which provide more detail, for popular areas.

If you are walking the Heysen Trail in South Australia, there are two excellent guide books (Northern and Southern), with log books readily available available which include maps that are adequate for most walkers. The CFS also publishes (Mapland) excellent map books, and these too are available from map and outdoor shops. Many downloadable walking brochures for our parks are available from the Department of Environment’s Parks SA website.

With digital maps readily available, many people are using mapping software to select just the relevant parts of maps and to enlarge these beyond the 1:50K scale than is usually available in printed maps, making it easier to see the contour and creek lines. If you are lucky enough to live in NZ, you can download 1:50,000 maps free of charge and even Australia has 1:250,000 maps for free download from Geoscience which are useful for getting the big picture and planning access roads.

Using Mapping Software

My apologies to Windows users for the following Mac centric discussion. 

As a MacBook Pro user I have used MacGPS Pro mapping software for many years to import my scanned maps, plot my routes and export the waypoints to my GPS. A print out of the waypoints file is an essential record of each waypoint’s  name, grid reference, comments, and elevation

One big advantage of mapping software is that it is possible to enlarge the map on screen to locate the exact position of known waypoints  or to determine the grid reference to 7 figure accuracy of any point you can see. Once you have decided on your waypoints you can rapidly link these to form a route, calculating distances and bearings automatically by dragging from point to point, and plotting a route elevation graph by selecting the route single click. The elevation graph is useful for estimating time to be taken.

From MacGPS Pro

The disadvantage of using a Macintosh is that without a Windows emulator, such as Bootcamp, and an installed version of Windows, OziExplorer software doesn’t work.

For older Macs (not using intel cpu) use Virtual PC or for new OS X Macs with the Intel CPU use either Bootcamp or emulation software called VirtualBox or ParallelsVirtualBox (Sun Microsystems Inc.) is free for personal use. It works in OS X on Intel Macs. (OziExplorer – Running OziExplorer on a MAC or Linux Computer )

There is a way to overcome this and that is to import the maps from the disc in .ecw format into a graphics program such as Graphic Converter, select the relevant part and then save as a PICT or TIFF file.  Some of the .ecw image files are small enough to import directly into a mapping program such as MacGPS Pro.

Often the .ecw image file will be accompanied by a matching .map calibration file and providing you keep it in the same folder as the ecw file, you can then import into MacGPS Pro and automatically calibrate the map. You could of course still do it the old way which was to scan and process a hard copy of the map.

Assuming there is no matching .map file available, calibrating a digital map using MacGPS Pro requires that you first rotate the map (using GraphicConverter) so the northing gridlines are horizontal and then enter the full 7 figure grid references of four widely spread points, usually near the corners of your map.

Top Left:  Easting 0263000 Northing 6540000, Grid Zone 54J, AGD94

From MacGPS Pro

You must also enter the UTM grid zone and know the projection and map datum eg I am using a portion of the Oraparinna map for a forthcoming trip

From MacGPS Pro

NB UTM Grid Zones is SA are either 52 (far west), 53 (west) or 54 (central and east)

Annotating your pdfs

Annotated portion of Oraparinna map

There are several programs (I use Skim) that allow you to annotate a pdf. This is particularly useful as it allows you to add grid references to the margins of your map (NB MacGPS Pro has a menu item “View/Gridlines” which does this automatically for you) and add notes about the route. Most programs allow you to add arrows showing routes and highlights. Once you have done this, you can export as a pdf and if you have the full version of Acrobat take advantage of its ability to reduce the file size significantly, to as much as a tenth.

Using Google Earth to Plan a Route

Google Earth can be used to visualize the route, finding 4WD tracks, checking whether creek lines are heavily vegetated and to see if ridges would be easier going. Cattle, goat and sheep tracks converging on a creek line probably indicates a waterhole, spring or a shallow crossing. Rainwater tanks, galvanised iron shelters, windmills and bores can sometimes be seen in Google Earth, even if they are not marked on the map.

Flinders Ranges: Google Earth screen capture

Simply import your .kml file showing your waypoints and then zoom in and tilt to see your route in 3D. Use a screen capture program, such as  Snapz Pro X, to capture pics of significant parts of the route, with your waypoints shown. Save these to your iPhone, camera or print, for later reference while on the walk.

NB I can never get my GPS waypoints to exactly match those in Google Earth, as I assume it uses a different map datum

Protecting your maps

One of the advantages of printing your maps from pdfs is that you can print them in A4 format which means they can either be laminated back-to-back or placed in a map case without the need for folding.

Other relevant posts

The Bushwalking Navigation series

Other Resources

Geoscience
Department of Environment’s Parks SA website
Bushwalk Australia Forum
Friends of the Heysen Trail

  Creative Commons LicenseThis article by Bush Walker is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

Uncategorized

Bushwalking Navigation | How far have I walked?

Leave a comment

Want to know how far you have walked or how far you still have to go? Which  tools can use to find this info? What pre-walk planning should you have done? What should you be doing while you are walking? Can your GPS be relied upon to give this information?

 Part 1 of this article was published separately but has now been merged with Part 2

Knowing how far you have walked can determine whether you have a safe trip. Without knowing the distance you have walked, and the time it has taken, you can’t estimate how long it will take you to get to your camp site and whether you will make it before nightfall.

The best way is to “thumb” your map as you walk along, so you know where you are at all times and use this information, along with your route plan, your average speed and time since starting, to work out how far you have walked. Your GPS can give you a good guide too, but over long distances your GPS can be significantly inaccurate and should not be relied upon as your sole source of this information, especially if you are moving slowly in difficult terrain.

Before you can work out how far you have walked, either you or your GPS need two bits of essential information

  1. where you started
  2. where you are now

The first should be easy, but the second can be much more difficult. You can make it easier for yourself by doing some preparation before you leave home and again at the start point (trailhead for those from NA).

Silva Map Measurer Plus

Before you leave home

  • purchase or download (lucky NZanders!) a map and guidebook if available.
  • use navigation software (smartphone or PC*) to explore your digital map, measure distances, select routes and waypoints
  • view the terrain in Google Earth or Google maps, select your waypoints, route and measure distances
  • enter way points into your GPS and link them as a route, using the software or just manually
  • measure distances using a map measurer or piece of cotton or a ruler, depending on whether the track is straight or windy
  • prepare a route plan
  • mark your map with your route and waypoints

* I have used MacGPS Pro for the last 10-15 years on my Mac.

    At the beginning of your walk
    • locate yourself on the map
    • check the time and start you stopwatch/timer
    • mark the start waypoint on your GPS and set it to navigate to your  next planned stop
    • reset the Trip Odometer on your GPS
    • reset your pedometer if you are carrying one

    PS don’t forget to adjust the time and date on your camera as well, as it is good to be able to match photos with your GPS location when you get back home.

    While you are walking

    • “thumb” your map, reading map-to-ground as you walk along, “ticking off” prominent features as you walk along
    • use your GPS, and known features, to work out your average speed and use your stopwatch, which you started at the beginning of the leg, to estimate how far you have walked, based on the average speed
    • continually check that the terrain matches where you should be on the map based on your average speed and time you have been walking, less breaks. This is a very difficult skill to learn and needs continual practice as it is very easy to miss a creek junction or mistake a knoll. Carry a map even on an easy day walk and practise.

    When you reach your objective

    • your objective should be a prominent feature which is on your map and your route plan. Use navigation techniques such as aiming off, handrails, catching features and attack points to help you locate the feature.
    • use your GPS to check your location, making sure you are using the correct map datum
    • use your route plan to look-up the distance, which you hopefully measured using one of the devices listed above before you set off
    • use your GPS’s Trip Odometer to tell you how far you have walked (subject to inaccuracies: read below)

    Why my GPS can’t measure distance travelled accurately.

    Your GPS trip odometer should only be used as a backup in determining distance, not as your primary device, as it is unable to accurately determine distance travelled in typical off track walking terrain, as occurs when you are walking along a windy creek track with tree cover, overhanging cliffs and the odd waterfall to climb. For most use on open tracks the accuracy will be adequate but for a 10 km walk leg through difficult terrain, the inaccuracy could be as much as 10-25% of  the true distance.(Source: Garmin Forums)

    One of the reasons for this is that the GPS adds the distances, as the “crow flys”, between the points it has saved, to the trip odometer and these will usually be slightly shorter that the actual distance you walked, especially if you have changed the data logging from the default which is usually once per second (1hz) to something less frequent. The only exception to this will be if you are walking in a straight line when it should be able to measure with 100% accuracy. The inaccuracy will be further increased if you make frequent stops, turn frequently or walk slowly, say less than 3.5 km/hr, so that the GPS doesn’t know you are walking. Walking up a steep incline can also produce inaccuracies, as the GPS only measures horizontal distances.

    The accuracy will be increased by increasing the data logging rate  eg 1Hz (once a second) to 5Hz. The problem with this is that your battery may not last as long and when you reach the internal memory limit it may start deleting the oldest.

    From the Garmin Forums: Distance of Trip odometer not the same than distance of Track

    When you walk (or drive), the GPS is constantly doing calculations based on where you are this instant compared to where you were on the previous location reading so it “knows” which direction you are traveling and how fast you are traveling.

    At each of these calculations, it also calculates the distance traveled and adds that to the Trip Odometer.

    Most GPS units do these calculations approximately once each second. You do not travel very far in one second, even in a motor vehicle traveling at the speed limit, so each of these calculated distances will be fairly accurate. That means when you add them all up, as the Trip Odometer is doing, the total distance in the Trip Odometer at the end of the trip will be fairly accurate.

    One thing that will affect the accuracy of the Trip Odometer when you are hiking is if you are not moving fast enough for the GPS to detect that you are moving. That could cause little pieces of travel to not get added into the Trip Odometer and the distance it reports to be shorter than reality.

    Track files are different. If you save the track log to a file, it always prunes the log to 500 track points, regardless how many points there are in the raw log file. If your driving or hiking was not in a long straight line, you will “lose” distance when pruning the points. That is, if you walked in a curve that originally had 20 points marked and the curve gets pruned to, say, 3 or 8 points to describe it in the track file, you will not get the full distance of the curve calculated in the track.

    That is because the calculations of distance in the track file all assume that the distance between each recorded point is a straight line. If you describe a curve with fewer points it will always look like the curve covers less distance.

    If you transfer the raw track log file to Mapsource or Basecamp, you should get all of the track points and that should cause less of a difference between the track and the related Trip Odometer reading.

    Further reading:

    Bushwalking Navigation | Using Topo50 Maps (LINZ) for Tramping in New Zealand
    Bushwalking Navigation | How to Choose the Best iPhone GPS App
    Bushwalking Navigation: The Importance of Using the Correct Geodetic Map Datum.
    Bushwalking Navigation | A Route Plan Workflow
    Silva Map Measurer Plus
    Bushwalking Photography Workflow | Share the Best of a Group’s Photos Using iPhoto

    Read more Navigation posts

      Creative Commons License This article by Bush Walker is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

    Uncategorized

    iPhone Apps for Bushwalkers Revisited

    Leave a comment

    It’s over a year since I began reviewing iPhone apps for bushwalkers. During this time I have tried hundreds and found that I only use a few regularly.

    While there are hundreds of iPhone apps useful to bushwalkers and growing every day, what you personally find useful is determined by your past experience, the type of walking you do, your interests,  and your willingness to be dependent on high tech devices.

    After trying most, I regulary use only a few of these. On bushwalks, my choice will vary as it is dependent upon on the duration of my walk, and hence how important it is to save battery power,  and upon how much non-walking time I will have available.

    My iPhone Apps

    Navigation: Bit Map, Declination, Maps, Google Earth, Compass
    Field Guides: Good Reader, BooksApp, Kindle, Aus. Birds (Morecomb), Field Guide Fauna Museum Victoria, Bird in Hand, WhatBirdNZ, Wikipanion, MyEnviro, FrogLog
    Bushcraft / Survival : KnotsGuide, SASSurvival, Knots, GoneTrekking
    Camp Food: Jamie Oliver’s Recipes, Poh’s Kitchen, Nigella Quick (….LOL)
    Fitness: Walkmeter, Beat Monitor, Cadence, iHandy Level
    Weather: Pkt Weather, Rainspotting, Clouds, iBarometer, ShralpTide, Clouds,WeatherNZ
    Travel: Frequent Flyer, Webjet, Plane Finder, Lonely Planet, Trip Advisor
    Astronomy: Star walk, Star Guide
    NZ: WeatherNZ, WhatBirdNZ, SnowReports
    Photography: Flickr
    Medical: Elastoplast, MediProfiles, St John NZ

    Disclaimer: Navigation using your iPhone always needs to be backed up with a compass, map and a dedicated GPS. 

    I have written reviews of many of these iPhone apps previously in this blog, several articles about how to use iPhone apps in general while bushwalking, and detailed articles which focus upon iPhone apps for navigation, fitness and NZ.

    Read more…..

      Creative Commons LicenseThis article by Bush Walker is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

    Uncategorized

    Bushwalking Navigation | How to Avoid Getting Lost or Losing Someone in Your Group

    1 Comment

    Have you ever been on a bushwalk and lost track of where you were? Ever turned the corner and found the rest of your group was no longer walking ahead? Ever stopped to take a photo and been unable to catch up with your group?

    Getting lost on a walk can easily be avoided by some pre-planning, good leadership and each walker taking responsibility for knowing where they are at all times.

    The Pre-planning

    All walkers should have a map of the walk.

    This could be a full topographic map or the relevant part of the map (A4), printed from a digital source or scanned from the original, and then laminated or inserted into a plastic pocket, which has been sealed. Before distributing a small part of the map make sure that the Eastings and Northings are clearly marked on the map, so a grid reference can be given and found. If the route has already been planned, show the route with dots or crosses and significant waypoints, which should be named.

    If you have some individuals who have a GPs, issue them with the waypoints and route so they can upload it before leaving home. If you issue the route as a .kml file then individuals can familiarise themselves with the route, by importing the waypoints into Google Earth. Issue a route plan which gives information about the legs of the walk, especially for those without a GPS.

    At the Start of the Walk.

    A good leader will always brief the group:

    • have everyone locate the starting point on their map
    • have everyone locate the finishing point on their map
    • give an ETA at the campsite and distance
    • outline the route, describe the terrain, point out significant obstacles
    • locate a lunch spot and approximate time

     Before starting appoint a “tail-end charlie” or “whip” to always be at the back and assist in keeping the group together. This person needs to have enough experience and confidence to know when to ask the leader for a break to rest tired individuals or to bring the group back together.

    Decide who will lead the way and brief them on how you want the group kept together: visual sight to the rear or maximum spread of 50m and/or pause at every junction. The trail-blazer needs to be a competent and strong bushwalker as they will often need to find the best route and break through bush.

    Check that everyone has the emergency equipment needed for an overnight stop caused by bad weather or an injury, appropriate clothing  and sufficient water before departure.

    During the Walk

    During the walk everyone should orientate and thumb the map so that they can follow their route as they walk. The leader/navigator should bring major features on the ground to everyone’s attention, so they can relocate themselves on the map. At each rest break make sure everyone knows where they are on the map.

    Individuals should try to match map-to-ground as they walk, anticipate approaching features such as creek bends, junctions and road intersections. Form a 3D image of the country you are walking through and make sure that what you can see fits with what you were expecting. Is the creek you are walking in following the direction the map shows? Is the creek running up hill or downhill? Does this match what the map shows?

    Keep you map orientated towards the north using your compass or the sun.

    What if you lose the rest of the group?

    • don’t panic
    • keep those “lost” together
    • try to work out where you are
    • head for a high point with your map, compass and phone and try to recognise features. Climb a tree if necessary.
    • If you can’t  see higher ground, head on a compass bearing which you think will most likely lead to higher ground.
    • don’t walk more than 1 km and continually check your bearings, so you don’t walk around in circles
    • return to a recognisable feature  by retracing your steps, taking a bearing before you start off
    • set up camp, build a shelter and conserve energy
    • if 3-4 hours have passed,  consider contacting emergency services or use you PLB.
    • blow your whistle: 3 blasts separated by a short gap. Signal with a torch
    • light a small fire: smokey in the day, bright at night

    What if you as leader lose part of your group?

    • do a quick recce (min gp of 4) in areas of high probability such as where they were last seen and return to this point
    • leave a small group here for an extended stay. They should light a visible fire.
    • carry out a search using the remaining members of the group
    • signal for the lost group with a single blast of a whistle, repeated
    • if 3-4 hours have passed,  consider the group totally lost and contact emergency services by sending two well equipped people with full details (equipment carried, health, contact details of NOK, bushwalking skills) of the lost group members or use you PLB
    • searchers give 1 blast, and those lost 3 blasts on their whistles

    Relevant Articles

    Bushwalking Navigation
    Bushwalking Navigation | A Route Plan Workflow
    Bushwalking Rescue: Emergency Beacons and Personal Tracking Systems
    A Guide to Better Bushwalking
    Map Reading Guide (GeoScience)

      Creative Commons License This article by Bush Walker is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

    Uncategorized

    Bushwalking Navigation | Using Creek Lines in Arid Environments

    Leave a comment

    Ever wondered why it is so easy to get lost following a creek in an arid environment? What precautions can you take? Why is it more difficult to navigate uphill than downhill?

    I have just come back from 4 days in the Vulkathunha-Gammon Ranges, over 700 km north of Adelaide where rainfall averages less than 20 mm per month with most of it falling during summer as the tail end of monsoons in the north west of Australia sweep down into northern South Australia and temperatures rise into the mid to high 30s. This has been one of the best start to the bushwalking season for many years and there are large numbers of full waterholes in the creek beds, lots of weed infestations and even a mouse plague.

    Walking is usually via dry rocky creeks beds, as the ridges are often steep, rugged and exposed. Sometimes the creeks are full of native vegetation such as paperbarks (Melaleuca) and flood debris which makes movement with a full pack difficult.

    Invariably navigation is a challenge, as few, if any, of the creeks have flowing water to help decide which way is downstream and it is difficult to distinguish major tributaries from mere gully’s. Often creek beds are hundreds of metres wide and may have islands in the middle, which can give the impression of a creek intersection, leading to miscounting.

    Creek navigation involves

    • starting from a known location (use your GPS)
    • deciding how far away the next creek intersection will be and whether it will be on the left or right
    • calculating your walking speed and using elapsed time as a guide to when the next intersection should occur
    • counting creek intersections as you go
    • checking map to ground as you walk for obvious features such a gorges, cliffs, bends in the creek and stopping if they don’t appear in the correct sequence and place
    • using your compass to check the direction of each creek at each intersection with that expected from the map
    • checking for debris against tree trunks and trickling creeks to decide which way the creek is flowing
    • checking your location frequently with your GPS, even if you think you know where you are, as often parallel creek beds, can appear to be very similar. 
    • deciding on a catching feature so you don’t go too far or a handrail you can follow (see below for glossary)

    If you have a GPS, then set up a route linking waypoints you have pre-determined at each creek intersection (decision point). This will give you distance to the next intersection, time to next intersection and bearing, but has severe limitations if the creek bed is very windy as all directions are “as the crow flies”. The GPS should never be relied upon without confirmation from map to ground, especially in narrow gorges where reception can be poor.

    Uphill navigation following creek lines is always more difficult than downhill, as there always at least two uphill choices at each intersection but coming downhill, it is unlikely that you would decide to go back uphill at the intersection, knowing that the main creek must be going downhill.

    Other Similar Posts

    Bushwalking Navigation | A Glossary of Frequently Used Terms 
    Bushwalking Navigation

      Creative Commons License This article by Bush Walker is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

    Uncategorized

    Bushwalking Navigation | A Glossary of Frequently Used Terms

    Leave a comment

    Have you ever wondered what SOG and VMG mean in the context of navigation? What is a breadcrumb trail? What is the difference between a backbearing and a resection? What are waypoints and how do they differ from a  grid reference?

    Glossary Terms Description
    .kml The KML file specifies a set of features (place marks, images, polygons, 3D models, textual descriptions, etc.) for display in Google Earth, Maps and Mobile, or any other 3D Earth browser (geobrowser) implementing the KML encoding. Each place always has a longitude and a latitude. KML files are very often distributed in KMZ files, which are zipped files with a .kmz extension.
    Aiming off Used to find an objective on a feature which is straight eg river, mountain ridge, road.
    Deliberately aim to strike the feature 10 ° to right or left of feature and then turn along feature to reach objective (also called
    Stefansson method or intentional error)
    Attack point A feature, which is near but much easier to find than your objective.
    Back Bearing Used to see if you have deviated from the intended path. Face starting point. Check that south end of needle is centred on mark.
    Bearing or Course A bearing is the angle between a line connecting two points and a north-south line.
    Breadcrumb trail  A track is a compilation of samples or “breadcrumbs” taken over a period of time.
    Calibration The process of inputting the grid references of known points, usually the four corners of a map.
    Catching feature Prominent features which are beyond your
    objective but     can act as safety net. A bearing on prominent feature at
    90 ° to direction of travel can be used.
    Coordinates In 3D latitude, longitude and elevation
    Easting, Northing The terms easting and northing are geographic Cartesian coordinates for a point. Easting refers to the eastward-measured distance (or the x-coordinate), while northing refers to the northward-measured distance (or the y-coordinate). (Wikipedia)
    Escape Route These are the routes you will take back to safety if anything prevents your progress to your destination. This could be an injury,
    the weather, too slow progress or physical blocking of your route by a landslide, avalanche, bushfire or flooded river.
    Grid Reference Numerical grid references consist of an even number of digits. Eastings are given before Northings. Thus in a 6 digit grid reference 123456, the Easting component is 123 and the Northing component is 456. (Wikipedia)
    Handrail Definite features which are roughly aligned with direction of travel and which make navigation easier. Don’t use creeks or gullies but may run parallel to them.
    Heading Compass heading or course measured from true or magnetic north.
    Map Datum The horizontal datum is the model used to measure positions on the earth. A specific point on the earth can have substantially
    different coordinates, depending on the datum used to make the measurement.
    (Wikipedia)
    Naismiths Rule A rule of thumb that helps in the planning of a walking or hiking expedition by calculating how long it will take to walk the route including ascents. (Wikipedia)
    Pacing A pace is the distance between each right foot hitting ground. For 1.8m person, with
    pack, ≈ 1.5m ie 660 paces to 1km.
    POI Points of Interest. Often downloaded in advance of a walk.
    Raster Map Made up of a grid of pixels also known as bitmap
    Resection Used to describe process of drawing three intersecting transect bearings to find your present location. Select features which are at a maximum angle to each other. eg 120 °
    Route Two or more waypoints
    Route Card The planned route is broken down into a series of legs, each of which begins and ends at a clearly defined feature, and which can be followed on a single compass bearing. In addition, distances, height gains
    and losses and times calculated using Naismith’s rule are included.(Wikipedia)
    SOG Speed over ground. The speed at which you are moving over the surface of the earth.
    Topographic Map A type of map characterized by large-scale detail and quantitative representation of relief, usually using contour lines.
    Track A track is a compilation of samples or “breadcrumbs” taken over a period of time. (MotionX GPS)
    Transect Bearing Useful to locate exact position on a handrail., by identifying a prominent feature and drawing a back bearing on the map to intersect the handrail.
    UTM Universal Transverse Mercator coordinate system; a grid-based method of mapping locations on the surface of the Earth
    (Wikipedia)
    Vector map Scaleable, small file size, where lines are specified by coordinates not pixels; not raster or bitmap.
    VMG Velocity made good. Effective speed at which you are approaching your waypoint.
    Waypoint Sets of coordinates which identify a point in space, often given as a grid reference.

    Related postings

    Bushwalking Navigation

      Creative Commons License This article by Bush Walker is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.

    Uncategorized

    Bushwalking Navigation | How to Choose the Best iPhone GPS App

    3 Comments

    Which navigation features do bushwalkers need?  Which features do a selection of the iPhone GPS apps have? How do you decide which of the iPhone navigation apps suits you best?

     There are thousands of navigation apps for the iPhone, but only a small number are designed for non-motorists. From these I have selected just a few supporting the iPhone’s built in GPS and compass sensors which could be suitable for the needs of bushwalkers, trampers and hikers. I was going to eliminate those that only use lat/long for locations or don’t have metric units, but there are many friends who read these blogsand who live in the USA.

    You should make your choice based upon your intended use, not on the number of features available, as often compromises need to be made by developers to fit in more features. Better to have a few key features fully developed and easy to use, than a multitude of features which are very limited in their capabilities.  Key deciding factors will be whether you wish to share your bushwalking with others via the web, whether you want to plan your hike using complementary desktop software and sync with your iPhone later and whether you really only want to view maps and need a limited set of GPS features.

    Free versions of apps are often available which allow you to test features before purchasing and this option should be fully explored. Beware of seemingly low priced apps that require you to purchase each additional map or pay to use their integrated website. Some apps may initially seem expensive, but come with a full quota of high quality 1:50K topo maps preloaded.

    A few of the most frequently mentioned iPhone navigation apps in bushwalking/hiking /tramping circles are

    Which are the features that the ideal bushwalk navigation app could possess?

    Disclaimer: The accuracy of the data in the table below is limited by the quality of the information supplied by the developer and, if critical, should be checked by emailing Support at the address above.

    Features MapApp NZ Mud Map Bit Map Motion X GPS Memory Map
    Offline Map Viewer, with fast scrolling and zooming
    •
    •
    •
    •
    •
    Ability to load, tile and show maps in a large number of formats
    #2.
    Aus,
    NZ

    #3
    • #5
    Limited
    #1
    #6
    Display current position centred on map and share in realtime
    • No

    sharing

    •
    •
    •
    •
    Display position coordinates in UTM and lat / long
    • #4
    •
    •
    •
    Support metric units
    •
    •
    •
    Show tracklog (route taken) and allow trackback.
    •
    •
    •
    •
    Create and edit waypoints and link to form routes
    •
    •
    •
    •
    Import/export waypoints, tracks and routes (multi format)
    •
    •
    •
    Share routes and waypoints via email, the web or Twitter
    •
    #5
    •
    •
    View SOG, VMG, distance to and bearing to waypoint.
    •
    Show current speed, max speed and time to destination
    Limited
    •
    Use compass to give current heading (course)
    •
    •
    •
    Display total ascent /descent and gradient graphs for a route
    •
    Live speed and altitude graphs.
    •
    •
    Show sunrise / sunset and tide times
    Placename index for searching
    •
    •
    •
    Voice announcements of user specified data
    •
    Desktop software which syncs with iPhone
    •
    Geotag waypoint and integrate photos taken along route
    •
    Background track logging with low battery consumption
    Multitask with audio and phone
    •
    Search | GoTo
    •
    •
    Links from POI to Wikipedia
    •
    •
    NOTES
    1 Limited access to topo maps for Australian bushwalking areas
    2 Topo50 NZ maps included in purchase price. One app for north island and one for south island, containing all NZ 50K maps
    3 Topo50 maps for NZ are available free of charge but you need to buy additional maps for Australia eg iTOPO 1:250,000 maps (4×4 and Outback touring) • Westprint Outback maps (4×4 and Outback touring) • Gregory’s touring maps (4×4 and Outback touring) • Melway Street Directories• VicMap  1:25K
    4 Lat / long only hence useless for bushwalkers but may be great for hikers.
    5 Can acquire maps, .kml, .kmz, zip, by email. Can use OziExplorer  maps or scanned and calibrated maps
    6 Limited access to USGS maps. Additional maps for a fee.Time limited Demo period on most maps to see if it is the map you want to buy and keep.

    Conclusions

    Unfortunately for trampers and bushwalkers there does not seem to be any ideal GPS app for the iPhone which also allows the use of high resolution uploaded maps. Either the maps available are of insufficient quality or if they are suitable then the GPS has limited features.

    • Bit Map allows the upload of high quality user supplied maps but has only a basic set of GPS features.
    • MotionX GPS has superb GPS features, equivalent of any dedicated GPS, but seems to lack suitable maps for Australian bushwalkers
    • MapApp NZ has superb free maps preloaded but, other than the ability to show current location, has  no other GPS features.
    • Memory Map has limited access to Australian maps but has a good range of GPS features.

    Related Postings

    Bushwalking Navigation | A Glossary of Frequently Used Terms 
    iPhone Navigation and Map Viewer App Review | Bit Map 3 by Nixanz
    Review: The iPhone’s Navigation Potential for Bushwalkers and Hikers 
    Bushwalking Navigation
    iPhone Apps
    GPS
    Maps

      Creative Commons License This article by Bush Walker is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.